The CBE and CBEPL anchors (with extender) are mechanical torque expansion anchors, supplied with threaded stud, washer, jacket and cone. Due to its threaded stud, it becomes one of the ideal anchors for fastening façades and Walsywa has one range of diameters ranging from 1/4″ to 1″.
| Description | Thread diameter | Hole diameter | Stud length | Jacket length | Length of the extender | Minimum hole depth | Max. thickness to be fixed | Tightening torque | Average loads* (kgf) | ||||
| Diameter A | Diameter B | c | d | e | f | g | N.m | Traction | Shear | ||||
| in. | in. | mm | in. | mm | mm | mm | in. | mm | mm | ||||
| CBE 14605** | 1/4″ | 3/8″ | 10 | 2 9/16″ | 65 | 32 | – | 1 5/8″ | 41 | 16 | 12 | 1127 | 800 |
| CBEPL 14090** | 3 9/16″ | 90 | 22 | 2 5/8″ | 66 | 20 | |||||||
| CBE 56075 | 5/16″ | 1/2″ | 13 | 3″ | 75 | 34 | – | 1 3/4″ | 44 | 22 | 25 | 1773 | 1190 |
| CBEPL 56100 | 4″ | 100 | 25 | 2 7/8″ | 73 | 25 | 1902 | ||||||
| CBE 38080 | 3/8″ | 9/16″ | 14 | 3 3/16″ | 80 | 37 | – | 1 7/8″ | 47 | 24 | 40 | 2143 | 1617 |
| CBEPL 38110 | 4 5/16″ | 110 | 25 | 3″ | 76 | 30 | 2753 | ||||||
| CBE 12095 | 1/2″ | 3/4″ | 19 | 3 1/4″ | 95 | 50 | – | 2 3/8″ | 60 | 26 | 100 | 2970 | 2897 |
| CBEPL 12135 | 5 9/16″ | 135 | 33 | 3 1/8″ | 99 | 30 | 4929 | ||||||
| CBE 58115 | 5/8″ | 7/8″ | 22 | 4 1/2″ | 115 | 60 | – | 2 3/4″ | 70 | 34 | 180 | 3333 | 4967 |
| CBEPL 58165 | 6 1/2″ | 165 | 45 | 4 1/4″ | 120 | 32 | 5841 | ||||||
| CBE 34145 | 3/4″ | 1″ | 26 | 5 3/4″ | 145 | 80 | – | 3 5/8″ | 92 | 32 | 350 | 4320 | 6573 |
| CBEPL 34220 | 9″ | 220 | 63 | 6 3/8″ | 162 | 50 | 6657 | ||||||
| CBE 10105 | 1″ | 1 1/4″ | 32 | 6 7/8″ | 175 | 100 | – | 4 5/8″ | 118 | 35 | 400 | 7790 | 12080 |
| CBEPL 10270 | 11″ | 270 | 79 | 5″ | 204 | 50 | 1676 | ||||||
* Loads obtained in 30 MPa strength concrete. Tests performed at the Walsywa Laboratory.
** Available with Grade 2 screws or studs (Gr. 2) and grade 5 (Gr.5) For Gr. 5, the average pulling load is 1395 kgf. Tightening torque for Gr. 5 is 25 N.m. Consider safety factors according to the table in the general catalog.
Image01: 1 Drill the hole with the indicated diameter and depth and then clean it;
Image02: 2 Insert the assembled anchor through the hole;
Image03: 3 Tighten the nut with the torque indicated in the table above;
Image04: 4 Loosen the nut, position the part to be clamped and give the final torque.
Concrete
Hollow Block
Rock
Drywall
Cement Board
Wall Panel
Wood
OSB
Structural Steel
Metal Tile
Aluminum
Guides and amounts
